Operation

You can run any zuul process with the -f option to make it not daemonize and stay in the foreground, logging to your terminal. It’s a good idea at first to check for issues with your configuration. There’s also a -d option to engage verbose debug logging, but be careful in busy deployments as this can generate very large logs.

To start, simply run:

zuul-scheduler

Before Zuul can run any jobs, it needs to load its configuration, most of which is in the git repositories that Zuul operates on. Start an executor to allow zuul to do that:

zuul-executor

Zuul should now be able to read its configuration from the configured repo and process any jobs defined therein.

Scheduler

Operation

To start the scheduler, run zuul-scheduler. To stop it, run zuul-scheduler stop.

Reconfiguration

Most of Zuul’s configuration is automatically updated as changes to the repositories which contain it are merged. However, Zuul must be explicitly notified of changes to the tenant config file, since it is not read from a git repository. Zuul supports two kinds of reconfigurations.

The full reconfiguration refetches and reloads the configuration of all tenants. To do so, run zuul-scheduler full-reconfigure. For example this can be used to fix eventual configuration inconsistencies after connection problems with the code hosting system.

To perform the same actions as a full reconfiguration but for a single tenant, use zuul-scheduler tenant-reconfigure TENANT (where TENANT is the name of the tenant to reconfigure).

The smart reconfiguration reloads only the tenants that changed their configuration in the tenant config file. To do so, run zuul-scheduler smart-reconfigure. In multi tenant systems this can be much faster than the full reconfiguration so it is recommended to use the smart reconfiguration after changing the tenant configuration file.

The tenant-reconfigure and smart-reconfigure commands should only be run on a single scheduler. Other schedulers will see any changes to the configuration stored in ZooKeeper and automatically update their configuration in the background without interrupting processing.

Advanced Options

These options are not necessary under normal conditions, but may be useful in some complex environments.

The --wait-for-init option (or ZUUL_WAIT_FOR_INIT environment variable) will cause the scheduler to wait until all tenants have been initialized before it begins processing pipelines. This may help large systems with excess scheduler capacity perform a rolling restart of schedulers more quickly.

The --disable-pipelines option (or ZUUL_DISABLE_PIPELINES environment variable) will cause the scheduler to silently discard all pipeline related events. This allows the scheduler to create and maintain all of the configuration of a running system without running any jobs or making any reports.

This option is not intended for normal use, and is only useful for certain testing and backup-related activities. Because any scheduler connected to ZooKeeper can process events, it does not make sense to mix values of this option. Normal production Zuul systems that are intended to process events should not set this option on any schedulers. To use this option on a standby or testing cluster, set it on all schedulers.

Backup and Restoration

While all of Zuul’s component services are designed to be run in a resilient active-active clustered deployment, a good disaster recovery plan should include backing up critical data. At a minimum, the randomly-generated project keys used for encryption of job secrets and SSH access should be backed up, as they cannot be recreated if lost. Zuul stores these keys in a keystore in ZooKeeper which is inconvenient to back up directly, but provides an administrative tool to export these keys to and import them from a local directory.

It’s highly recommended to set up periodic automation for dumping such an export to a secure location (for example, on the filesystem of each Zuul Scheduler) for use in a disaster where all ZooKeeper content is lost. You may also consider configuring a safe remote backup of these files with the tool of your choice, but be aware that they are potentially sensitive since anyone who gains access to them could decrypt job secrets or access protected systems which have been instructed to trust those keys.

Note that the exported keys are symmetrically encrypted with the same keystore.password which is used for encrypting and decrypting the copy of them in ZooKeeper, because its the encrypted versions of the keys which are exported and imported. Someone with access to the keys would also need a copy of the keystore.password from Zuul’s configuration, so for security-sensitive environments you may not want to back them up together. Conversely, if you lose the keystore.password then you also lose the use of the project keys in the keystore and any exports, so you will likely want to make sure you keep a secured copy of it somewhere as well in the event your server configuration is lost.

Merger

Operation

To start the merger, run zuul-merger.

In order to stop the merger and under normal circumstances it is best to pause and wait for all currently running tasks to finish before stopping it. To do so run zuul-merger pause.

To stop the merger, run zuul-merger stop. This will wait for any currently running merge task to complete before exiting. As a result this is always a graceful way to stop the merger. zuul-merger graceful is an alias for zuul-merger stop to make this consistent with the executor.

Executor

Operation

To start the executor, run zuul-executor.

There are several commands which can be run to control the executor’s behavior once it is running.

To pause the executor and prevent it from running new jobs you can run zuul-executor pause.

To cause the executor to stop accepting new jobs and exit when all running jobs have finished you can run zuul-executor graceful. Under most circumstances this will be the best way to stop Zuul.

To stop the executor immediately, run zuul-executor stop. Jobs that were running on the stopped executor will be rescheduled on other executors.

The executor normally responds to a SIGTERM signal in the same way as the graceful command, however you can change this behavior to match stop with the executor.sigterm_method setting.

To enable or disable running Ansible in verbose mode (with the -vvv argument to ansible-playbook) run zuul-executor verbose and zuul-executor unverbose.

Ansible and Python 3

As noted above, the executor runs Ansible playbooks against the remote node(s) allocated for the job. Since part of executing playbooks on remote hosts is running Python scripts on them, Ansible needs to know what Python interpreter to use on the remote host. With older distributions, /usr/bin/python2 was a generally sensible choice. However, over time a heterogeneous Python ecosystem has evolved where older distributions may only provide Python 2, most provide a mixed 2/3 environment and newer distributions may only provide Python 3 (and then others like RHEL8 may even have separate “system” Python versions to add to confusion!).

Ansible’s ansible_python_interpreter variable configures the path to the remote Python interpreter to use during playbook execution. This value is set by Zuul from the python-path specified for the node by Nodepool; see the nodepool configuration documentation.

This defaults to auto, where Ansible will automatically discover the interpreter available on the remote host. However, this setting only became available in Ansible >=2.8, so Zuul will translate auto into the old default of /usr/bin/python2 when configured to use older Ansible versions.

Thus for modern Python 3-only hosts no further configuration is needed when using Ansible >=2.8 (e.g. Fedora, Bionic onwards). If using earlier Ansible versions you may need to explicitly set the python-path if /usr/bin/python2 is not available on the node.

Ansible roles/modules which include Python code are generally Python 3 safe now, but there is still a small possibility of incompatibility. See also the Ansible Python 3 support page.

Log streaming

The log streaming service enables Zuul to show the live status of long-running shell or command tasks. The server side is setup by the zuul_console: task built-in to Zuul’s Ansible installation. The executor requires the ability to communicate with this server on the job nodes via port 19885 for this to work.

The log streaming service spools command output via files on the job node in the format /tmp/console-<uuid>-<task_id>-<host>.log. By default, it will clean these files up automatically.

Occasionally, a streaming file may be left if a job is interrupted. These may be safely removed after a short period of inactivity with a command such as

find /tmp -maxdepth 1 -name 'console-*-*-<host>.log' -mtime +2 -delete

If the executor is unable to reach port 19885 (for example due to firewall rules), or the zuul_console daemon can not be run for some other reason, the command to clean these spool files will not be processed and they may be left behind; on an ephemeral node this is not usually a problem, but on a static node these files will persist.

In this situation, Zuul can be instructed to not to create any spool files for shell and command tasks via setting zuul_console_disabled: True (usually via a global host variable in inventory). Live streaming of shell and command calls will of course be unavailable in this case, but no spool files will be created.

For Kubernetes-based job nodes the connection from the executor to the zuul_console daemon is established by using kubectl port-forward to forward a local port to the appropriate port on the pod containing the job node. If the Kubernetes user is not bound to a role that has authorization for port-forwarding, this will prevent connection to the zuul_console daemon.

Web Server

Operation

To start the web server, run zuul-web. To stop it, kill the PID which was saved in the pidfile specified in the configuration.

Finger Gateway

Operation

To start the finger gateway, run zuul-fingergw. To stop it, kill the PID which was saved in the pidfile specified in the configuration.